Home > Products > AT9532
Part Number Description Max frequency (kHz) I2C Adress Vcc Range(V) Interrupt 5V-to lerant I/O Output type max I/O voltage tolerance Number of I/Os Standby Current Max Output device current Default POR Output State Hardware Reset input Configuration Registers I/O Pull-Up Number of Device Address Cross Reference Pin/Package
AT9532 400 1100xxx 2.3~5.5 Open-Drain 5.5V 16 2.1μA 25mA Hi-Z Input 8 PCA9532 LP3943 CAT9532 TSSOP24 QFN24

General description

      The AT9532 is a 16-bit I2C-bus and SMBus I/O expander optimized for dimming LEDs in256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications.

     The AT9532 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED.

     The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus master is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 second. The open-drain outputs directlydrive the LEDs with maximum output sink current of 25 mA per bit and 200 mA per package (100 mA per octal).

     To blink LEDs at periods greater than 1.69 second the bus master (MCU, MPU, DSP,chip set, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the AT8575 or AT9555. Any bits not used for controlling the LEDs can be used for General Purposeparallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans,etc.

     The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes there gisters to their default state, all zeroes, causing the bits to be set HIGH (LED off).

     Three hardware address pins on the AT9532 allow eight devices to operate on the samebus.

Features and benefits

  • 16 LED drivers (on, off, flashing at a programmable rate)

  • Two selectable, fully programmable blink rates (frequency and duty cycle) between0.591Hz and 152Hz (1.69 second and 6. 58 milliseconds)256 brightness steps

  • Input/outputs not used as LED drivers can be used as regular GPIOs

  • Internal oscillator requires no external components

  • l2C-bus interface logic compatible with SMBus.

  • Internal power-on reset

  • Noise filter on SCL /SDA inputs

  • Active LOW reset input

  • 16 open-drain outputs directly drive LEDs to 25mA

  • Controlled edge rates to minimize ground bounce.

  • No glitch on power-up

  • Supports hot insertion

  • Low standby current

  • Operating power supply voltage range of 2.3V to 5.5Vв  

  • 0Hz to 400kHz clock frequency

  • ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101

  • Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA

  • Packages offered: SO24, TSSOP24, HVQFN24


  • 微信图片_20200617110557.png

Support:万广互联 Copyright © 2008-2020 Analog Tek Technology Co, Ltd 鄂ICP备20005446号-1